1. Introduction

This specification defines the core code and services that are required for an implementation of the Pre-EFI Initialization (PEI) phase of the Platform Initialization (PI) specifications (hereafter referred to as the “PI Architecture”). This PEI core interface specification (CIS) does the following:

• Describes the basic components of the PEI phase

• Provides code definitions for services and functions that are architecturally required by the UEFI PI working group (PIWG)

• Describes the machine preparation that is required for subsequent phases of firmware execution

• Discusses state variables that describe the system restart type

See Section 1.2 for more information.

1.1. Principle of Inclusive Terminology

The UEFI Forum follows a Principle of Inclusive Terminology in building and maintaining content for specifications. This means that efforts are made to ensure that all wording is perceived or likely to be perceived as welcoming by everyone regardless of personal characteristics. In some cases, the Forum acknowledges that wording derived from earlier work, for example references to legacy specifications not controlled by the Forum, may not follow this principle. In order to preserve compatibility for code that reads on legacy specifications, particularly where that specification is no longer under maintenance or development, language in this specification may appear out of sync with the Principle. The Forum is resolved to work with other standards development bodies to eliminate such examples over time. In the meanwhile, by acknowledging and calling attention to this issue the hope is to promote discussion and action towards more complete use of Inclusive Language reflective of the diverse and innovative population of the technical community that works on standards.

1.2. Organization of the PEI CIS

This PEI core interface specification is organized as shown in “Organization of the PEI CIS.” Because the PEI Foundation is just one component of a PI Architecture-based firmware solution, there are a number of additional specifications that are referred to throughout this document.

Table 1.1 Organization of the PEI CIS

Section	Description
Overview	Describes the major components of PEI including the PEI Services boot mode PEI Dispatcher and PEIMs
PEI Services Table	Describes the data structure that maintains the PEI Services
Services PEI Services	Details each of the functions that comprise the PEI Services
PEI Foundation	Describes the PEI Foundation and its methods of operation and the PEI Dispatcher and its associated dependency expression grammar
PEIMs	Describes the format and use of the Pre EFI Initialization Module PEIM
Architectural PPIs	Contains PEIM to PEIM Interfaces PPIs that are used by the PEI Foundation
Additional PPIs	Contains PPIs that can exist on a platform
SPEI to DXE Handoff	Describes the state of the machine and memory when the PEI phase invokes the DXE phase
Boot Paths Boot	Describes the restart modalities and behavior supported in the PEI phase
PEI Physical Memory Usage	Describes the memory map and memory usage during the PEI phase
Special Paths Unique to the Itanium Processor Family	Contains flow during PEI that is unique to the Itanium processor family
Security SEC Phase Information	Contains an overview of the phase of execution that occurs prior to PEI
Dependency Expression Grammar	Describes the BNF grammar for a tool that can convert a text file containing a dependency expression into a dependency section of a PEIM stored in a firmware volume
TE Image	Describes the format of the TE executable
TE Image Creation	Describes how TE executables are created from PE32 executables
TE Image Loading	Describes how TE executables are loaded into memory

1.3. Conventions Used in this Document

This document uses the typographic and illustrative conventions described below.

1.3.1. Data Structure Descriptions

Supported processors are “little endian” machines. This distinction means that the low-order byte of a multibyte data item in memory is at the lowest address, while the high-order byte is at the highest address. Some supported processors may be configured for both “little endian” and “big endian” operation. All implementations designed to conform to this specification will use “little endian” operation.

In some memory layout descriptions, certain fields are marked reserved. Software must initialize such fields to zero and ignore them when read. On an update operation, software must preserve any reserved field.

The data structures described in this document generally have the following format:

Structure Name: The formal name of the data structure.

Summary: A brief description of the data structure.

Prototype: A “C-style” type declaration for the data structure.

Parameters: A brief description of each field in the data structure prototype.

Description: A description of the functionality provided by the data structure, including any limitations and caveats of which the caller should be aware.

Related Definitions: The type declarations and constants that are used only by this data structure.

1.3.2. Procedure Descriptions

The procedures described in this document generally have the following format:

ProcedureName(): The formal name of the procedure.

Summary: A brief description of the procedure.

Prototype: A “C-style” procedure header defining the calling sequence.

Parameters: A brief description of each field in the procedure prototype.

Description: A description of the functionality provided by the interface, including any limitations and caveats of which the caller should be aware.

Related Definitions: The type declarations and constants that are used only by this procedure.

Status Codes Returned: A description of any codes returned by the interface. The procedure is required to implement any status codes listed in this table. Additional error codes may be returned, but they will not be tested by standard compliance tests, and any software that uses the procedure cannot depend on any of the extended error codes that an implementation may provide.

1.3.3. Instruction Descriptions

A dependency expression instruction description generally has the following format:

InstructionName The formal name of the instruction.

Syntax: A brief description of the instruction.

Description: A description of the functionality provided by the instruction accompanied by a table that details the instruction encoding.

Operation: Details the operations performed on operands.

Behaviors and Restrictions: An item-by-item description of the behavior of each operand involved in the instruction and any restrictions that apply to the operands or the instruction.

1.3.4. PPI Descriptions

A PEIM-to-PEIM Interface (PPI) description generally has the following format:

PPI Name: The formal name of the PPI.

Summary: A brief description of the PPI.

GUID: The 128-bit Globally Unique Identifier (GUID) for the PPI.

Protocol Interface Structure: A “C-style” procedure template defining the PPI calling structure.

Parameters: A brief description of each field in the PPI structure.

Description: A description of the functionality provided by the interface, including any limitations and caveats of which the caller should be aware.

Related Definitions: The type declarations and constants that are used only by this interface.

Status Codes Returned: A description of any codes returned by the interface. The PPI is required to implement any status codes listed in this table. Additional error codes may be returned, but they will not be tested by standard compliance tests, and any software that uses the procedure cannot depend on any of the extended error codes that an implementation may provide.

1.3.5. Pseudo-Code Conventions

Pseudo code is presented to describe algorithms in a more concise form. None of the algorithms in this document are intended to be compiled directly. The code is presented at a level corresponding to the surrounding text.

In describing variables, a list is an unordered collection of homogeneous objects. A queue is an ordered list of homogeneous objects. Unless otherwise noted, the ordering is assumed to be First In First Out (FIFO).

Pseudo code is presented in a C-like format, using C conventions where appropriate. The coding style, particularly the indentation style, is used for readability and does not necessarily comply with an implementation of the Unified Extensible Firmware Interface Specification (UEFI 2.0 specification).

1.4. Requirements

This document is an architectural specification that is part of the Platform Initialization Architecture (PI Architecture) family of specifications defined and published by the Unified EFI Forum. The primary intent of the PI Architecture is to present an interoperability surface for firmware components that may originate from different providers. As such, the burden to conform to this specification falls both on the producer and the consumer of facilities described as part of the specification.

In general, it is incumbent on the producer implementation to ensure that any facility that a conforming consumer firmware component might attempt to use is present in the implementation. Equally, it is incumbent on a developer of a firmware component to ensure that its implementation relies only on facilities that are defined as part of the PI Architecture. Maximum interoperability is assured when collections of conforming components are designed to use only the required facilities defined in the PI Architecture family of specifications.

As this document is an architectural specification, care has been taken to specify architecture in ways that allow maximum flexibility in implementation for both producer and consumer. However, there are certain requirements on which elements of this specification must be implemented to ensure a consistent and predictable environment for the operation of code designed to work with the architectural interfaces described here.

For the purposes of describing these requirements, the specification includes facilities that are required, such as interfaces and data structures, as well as facilities that are marked as optional.

In general, for an implementation to be conformant with this specification, the implementation must include functional elements that match in all respects the complete description of the required facility descriptions presented as part of the specification. Any part of the specification that is not explicitly marked as “optional” is considered a required facility.

Where parts of the specification are marked as “optional,” an implementation may choose to provide matching elements or leave them out. If an element is provided by an implementation for a facility, then it must match in all respects the corresponding complete description.

In practical terms, this means that for any facility covered in the specification, any instance of an implementation may only claim to conform if it follows the normative descriptions completely and exactly. This does not preclude an implementation that provides additional functionality, over and above that described in the specification. Furthermore, it does not preclude an implementation from leaving out facilities that are marked as optional in the specification.

By corollary, modular components of firmware designed to function within an implementation that conforms to the PI Architecture are conformant only if they depend only on facilities described in this and related PI Architecture specifications. In other words, any modular component that is free of any external dependency that falls outside of the scope of the PI Architecture specifications is conformant. A modular component is not conformant if it relies for correct and complete operation upon a reference to an interface or data structure that is neither part of its own image nor described in any PI Architecture specifications.

It is possible to make a partial implementation of the specification where some of the required facilities are not present. Such an implementation is non-conforming, and other firmware components that are themselves conforming might not function correctly with it. Correct operation of non-conforming implementations is explicitly out of scope for the PI Architecture and this specification.

1.5. Conventions used in this document

1.5.1. Number formats

A binary number is represented in this standard by any sequence of digits consisting of only the Western-Arabic numerals 0 and 1 immediately followed by a lower-case b (e.g., 0101b). Underscores or spaces may be included between characters in binary number representations to increase readability or delineate field boundaries (e.g., 0 0101 1010b or 0_0101_1010b).

A hexadecimal number is represented in this standard by 0x preceding any sequence of digits consisting of only the Western-Arabic numerals 0 through 9 and/or the upper-case English letters A through F (e.g., 0xFA23). Underscores or spaces may be included between characters in hexadecimal number representations to increase readability or delineate field boundaries (e.g., 0xB FD8C FA23 or 0xB_FD8C_FA23).

A decimal number is represented in this standard by any sequence of digits consisting of only the Arabic numerals 0 through 9 not immediately followed by a lower-case b or lower-case h (e.g., 25).

This standard uses the following conventions for representing decimal numbers:

• the decimal separator (i.e., separating the integer and fractional portions of the number) is a period;

• the thousands separator (i.e., separating groups of three digits in a portion of the number) is a comma;

• the thousands separator is used in the integer portion and is not used in the fraction portion of a number.

1.5.2. Binary prefixes

This standard uses the prefixes defined in the International System of Units (SI) (see http://www.bipm.org/en/si/si_brochure/chapter3/prefixes.html ) for values that are powers of ten.

Table 1.2 SI prefixes

Factor	Factor	Name	Symbol
103	1,000	kilo	K
106	1,000,000	mega	M
109	1,000,000,000	giga	G

This standard uses the binary prefixes defined in ISO/IEC 80000-13 Quantities and units – Part 13: Information science and technology and IEEE 1514 Standard for Prefixes for Binary Multiples for values that are powers of two.

Table 1.3 Binary prefixes

Factor	Factor	Name	Symbol
210	1,024	kibi	Ki
220	1,048,576	mebi	Mi
230	1,073,741,824	gibi	Gi

For example, 4 KB means 4,000 bytes and 4 KiB means 4,096 bytes.